Flower Power

The previous owner left a concrete base in our backyard. It's hollow in the middle but I figured it would make a decent side table if a top was added. I planned on cutting and staining a simple disk but then got inspired to try something more ornate. I used different colors of outdoor stain and then put a couple layers of weather sealant on to protect the unstained areas.

A good learning experience

The cladding project I began several weeks ago is finally finished. Most of the cladding was glued on with construction adhesive, brads were added to several of the side pieces and screws were countersunk into the front pieces. Some of this proved tricky as the 'carcass' I was cladding was made of old fiberboard. It was dried out, which didn't leave much grip for nails or screws, and had water damage in a few areas (leaving uneven surfaces). I came up with a bunch of creative workarounds and am glad this one is finished.

Liftoff!

I really should have followed my intuition and stopped and shifted gears with this project when the brown paint proved difficult to strip. I got a layer of stain on, only to be disappointed with the results. The wood didn't turn out to be very interesting (in terms of grain patterns) and proved difficult to work with. The result was a blotchy mess:

I thought about doing the antique patina look I previously considered but then decided to try something more whimsical. The dimensions of this shelf reminded me of something I saw over on Ana White's site and I decided to give that a try.

With the shelf unit already built, I used some plywood scraps to make the rocket fins and nosecone. The latter was made from 3-ply material and getting  good 45 degree edges was a little tricky. I thought it would be simpler to build it with flush edges but in hindsight something with overhang as shown in the plans is probably the way to go.

Preview of the next project

The (for now) final storage project for my son's room involves yet another old shelf from the garage. This thing is a real piece of junk. It's made of MDF, has really ugly veneers and trim pieces and the previous owner started priming it and then abandoned the project.

I thought about priming and painting the whole thing but figured that would only marginally improve things. I could get a better color but I'd still have a lot of poor surfaces and think it would look like a slapped a coat of paint on a piece of junk. Instead I found some inspiration from a project over at Instructables.

I'll be cladding the sides and front of my unit in pallet wood, repainting the inside and adding a stained wood top. The first step was to run some pallet wood through the jointer and cut to length. In this case I'll probably be gluing the jointed edge to the shelf and allowing the uneven surfaces to create some texture (opposite of what I did with the smaller shelf unit). The next step is to clean up all these boards with the jointer or a sander and decide which ones get painted and which stained.

Another restoration

I found another old shelf that could be upcycled for storage in our son's room. I'm trying to add more 'in process' photos to these posts so here goes.

The shelf was covered in a dull brown paint and was in pretty beat-up condition. As I was cleaning it up, I noticed raised nails and some weird kind of staples. The former were easy enough to pound in but the latter required a lot of careful filing. There's a lot of ways to join wood, I recommend choosing anything other than protruding metal.

I started stripping with a random orbit sander and then switched to the belt sander as the brown paint was very thick and strong. The shelf unit wasn't assembled very well and there were a lot of uneven surfaces and protruding points. It broke a belt on the belt sander and started shredding a disk on the random orbit sander. Nice. What I should have done was primed over the brown paint, added a top coat of white, spot sanded and stained the whole thing. That would have given me an antiqued look with a nice patina of brown, stained white and stained bare wood.

Alas, I was committed and decided to bring out the heavy artillery. Chemical stripper is great for uneven surfaces but is a real mess to work with. The stripper took off 90% of the brown paint, leaving a couple standing blotches and a brown color to the wood. Spot sanding took care of both of these issues.

After all the difficulty with the outer surfaces, I figured there was no way I was going to get the brown paint off the inside. I did a quick sanding to rough things up, put on a layer of primer and finished with a new coat of brown paint. The outside was stained and is drying overnight. Tomorrow, I'll decide if it needs a second coat and start with the polyurethane.

A 'quick' restoration

Well, as quick as anything is around here these days. Our newborn son has arrived and his room is a little short on storage. This table was left on our patio by the previous owner. The bottom shelf was decomposing MDF and the top was a couple of paving squares. I know, weird. I stripped everything down and repainted the frame. The old shelves were tossed out and replaced with pallet wood. 

For the new shelves, I used a couple new toys in my shop. The boards were run through a jointer and then ripped and cut to length on a bandsaw. I went back to the jointer to clean up the ripped edges. This gave me a relatively flat surface and enough straight edges for a glue-up. I belt sanded the 'flat' side to even things out and then applied stain and polyurethane. The bottom is unfinished and extremely uneven but that doesn't matter in this case. To get both sides flat I'd need a thickness planer but that's a toy for another day.

If in doubt, prime

My wife painted the doors on her studio. The manufacturer told us they were painted "primer white." Well that must be a color as it sure as heck wasn't primer. When in doubt, use primer. Even if you don't need it for adhesion purposes, it can reduce the number of color coats you'll need. Better to spend a little more time up front than having to redo the whole project.

Studio Plank

We had a detached bungalow built for my wife's custom design studio. She wanted a barn wood style ceiling and we decided to use reclaimed pallet wood. The end result turned out really well and as usual we learned some good lessons along the way:

- Older pallets will have wood with the most character but will also be hardest to break down. I used a reciprocating saw and highly recommend that method.

- The downside of using the reciprocating saw is you end up with nail heads in all your boards. You'll need to tap those out if you're going to run the wood through a jointer or planer. If not, just leave them in. They'll enhance the rustic look of the finish product and save you a LOT of time.

- We used a water based stain. That makes for easy clean up but you get a flatter finish than you would with oil based stain. We compensated by thinning the stain out to various degrees. Between different concentrations of stain and the different absorbency of each board we got the mottled look shown in the photo.

- If you're not going to mill the boards, you will have small gaps between them. We used plywood instead of sheetrock and stained it a dark brown. This makes the gaps unnoticeable unless you're on a ladder and looking right at them.

- We sorted the boards into piles of similar width and used these to make rows. Our contractor used a table saw to rip the boards in each row to identical width. So, each row is a different width but the boards within it are the same width. This made for relatively easy installation while still preserving a mottled, rustic look.

Order of Operations

We had a pergola built on our back porch. In order to save some money, I agreed to apply the wood stain myself. I insisted on the contractor having the wood delivered well ahead of when he would need it so I could stain it on the ground and am very glad I did so. It turned out to be a real bear of a job, moving 10' posts and 12' boards. I had to do some touch up work after it was built and can't imagine having to stain the whole thing like that. Working upside down atop an 8' ladder and trying to get into tight corners is not how you want to spend your Saturday. The lesson is figure out what's going to be easiest for you and stick with it. The pros might do it differently and they may be 'right' but they also have years of practice and special equipment. 

Oh and one other note, use oil based stain or, if you live in the People's Republic of California, stain with the highest oil content you can find. It will go on MUCH easier. Lowes has a better selection of 'high oil' stains than Home Depot.

Changing Table

This was a fairly simple project but it did yield a an important lesson. I started with an old computer desk and set out to repurpose it as a baby changing table. Tasks involved sanding the old finish, repainting, routing the door and drawer edges, adding new hardware and installing trim pieces on the top to help keep the changing pad and supplies in place.

My original plan was to strip the original finish, apply new paint and then antique it by sanding the edges and applying a thin layer of dark stain. I did all this on a door from a hutch not used in the conversion and am glad I used the test piece. It turned out the original finish was so strong that the stain would dye the paint but wouldn't do anything to the wood I exposed in the sanding step. I ended up forgoing the antiquing step but may revisit that with dark wood wax in the future.

The Man's Desk

We'll start out with something (mostly) positive. This project was inspired by a plan for a table on Art of Manliness. I wanted to build something like that for my porch but most of my projects go better the second time so I figured I'd try using the plan on something else first. Coincidentally, I was in need of a new desk and had an old door that was in need of repurposing. I modified the table plans so that the base was standing height and fit the dimensions of the old door.

The end result turned out pretty well. The desk is serving its function well and I've received lots of compliments on it. Getting it built was a real bear and I learned several lessons along the way. In no particular order:

- A 7" circular saw is a very versatile tool but has its limits. Cutting through 4x4s requires a pass on either side and no matter how careful you are they will be slightly off. I tried leveling the cut ends with a belt sander, some files and 'touch ups' with the circular saw. That all helped a little but in the end the weight of the door is what keeps the whole thing level. Next time, I'll find access to a table saw or use two 2x4s attached to one another as an L.

- Dimensional lumber is never perfectly straight. Sometimes that's not a big problem but a small warp or curve is magnified when making something six feet long. This problem is compounded when working with tools like the circular saw. Guides and fences can help but have their limitations. 'Stationary' tools like a table saw are better; correcting your stock with a jointer and planer is best.

- Water based stain is great for clean up but produces a much 'flatter' look that you'll get with oil based stain.

- Priming is not a step worth skipping. I originally planned to strip the paint off the old door and stain it. The chemical stripper took the top coat of paint off easily but barely touched the primer underneath. I could have belt sanded the primer off but figured it would be easier to just repaint. Fine idea but I should have put fresh primer down first. I used latex paint and it didn't have the best grip with the old primer. That made for a lot of extra touch-up work.

- A dry fit will help you catch big/obvious problems but be prepared for some additional changes when you do set the screws and bolts. Remember the aforementioned issues with dimensional lumber and imprecise cutting tools? They all add up and when things are pulled into final shape some dimensions will change. In my case the footrest was measured to overhang the cross pieces by 1/4". After tightening the bolts my overhang disappeared. In hindsight, I should have cut it a little longer and planned to trim it to final size after assembly.

- I had a weird issue with the brown paint. Each time I touched-up a spot, it dried a slightly different shade. The best solution I found was to 'blend' it by sanding it and the surrounding area with 220 grit sandpaper. When the sanded area was covered with Varathane it matched its surroundings well enough to be unnoticeable.

Here's some more pics of the finished product: